HyGeoWorks
🔒 Previews run in your browser (WebAssembly) · Inputs are sent only when you formally export
AASHTO LRFD Sec. 11 (9th Ed. values) · State DOT φ Override · ACI 318 & ASTM A615 #4–#9

Cantilever & Gravity Retaining Wall Calculator — AASHTO LRFD Sec. 11 Strength Ia / Ib, State DOT φ Override & ACI 318

Retaining wall stability and RC check with US customary inputs (ft, in., pcf, psf, psi). The calculation core evaluates AASHTO LRFD Sec. 11 Strength Ia / Ib sliding, eccentricity and bearing (default φ_τ = 0.80, φ_b = 0.55; custom State DOT resistance factors can be entered and are flagged in the basis line of the result), reports the sliding and overturning factors of safety alongside, and tabulates ACI 318 flexural and shear design with ASTM A615 Grade 60 bars (#4 through #9). AASHTO LRFD 4th Ed. (2007) / FHWA-NHI-10-024 and FHWA-NHI-06-089 allowable stress design can be selected as alternative bases in the calculator.

Standards and references (context for this calculation; the basis the calculator applies is the one stated below):

Design basis for this page ▾
FHWA GEC 11 (FHWA-HIF-24-002, 2023) / SCDOT GDM (2022) / MnDOT LRFD BDM — AASHTO LRFD Bridge Design Specifications Sec. 11 resistance and load factors (9th Edition, 2020, as reproduced in these manuals)AASHTO LRFD Bridge Design Specifications, 4th Ed. (2007) / FHWA-NHI-10-024 (selectable)FHWA-NHI-06-089 Soils and Foundations Reference Manual Vol. II (2006) §10.5.5 (ASD, selectable)ACI 318 RC Flexural & Shear Design Table with ASTM A615 Grade 60 RebarState DOT Custom φ_τ / φ_b Override (entered by the engineer; flagged in the basis line of the result)

Design basis as reported by the calculation core: FHWA GEC 11 (FHWA-HIF-24-002, 2023) / SCDOT GDM (2022) / MnDOT LRFD BDM — AASHTO LRFD Bridge Design Specifications Sec. 11 (9th Ed. 2020 values as published in these free federal/state manuals; not the 10th Ed. text)

Recalculates in your browser as you edit inputs; Free sample Word report and DXF for this calculator; With a license: formal Word and DXF export, plus online project reports from the Project List; 3D schematic: fixed example, not drawn from your inputs.

Interactive US Customary Engineering Workstation
US customary inputs, shown as US (SI) in the results
Free Samples and Pricing
A public sample produced by the production service from this page's standard example and sealed with a verification code: open it in Word or AutoCAD and check it on the Verify page. Not for PE sealing or submittal.
Single-export pass: US$19 for one calculator, 3 formal exports in total within 24 hours of the first; full credit toward an upgrade within 30 days, full refund before the first export
Single-export passes (one calculator, 3 exports within 24 hours), 30-day passes, annual plans and perpetual licenses; printable quotes for purchase orders.
Formal export and the Project List are on the workbench toolbar above:
Licensed users can formally export this calculator's Word report (with a verification code and server time witness) and AutoCAD DXF drawing, or add several calculators to the free Project List and export a multi-chapter project report online, with nothing to install on a Mac. Projects with DEM terrain or GIS files can run in the heavy cloud computation or in the HydroStudio desktop edition.
The summary lists the basis, key results and check verdicts; its first line marks it as an online preview, not for PE sealing or submittal.
Download the Offline Workbench (Single HTML File, 39 Tools)
No install and no email required. It contains the same calculation core as this site; results are also a preview, not for sealed submittals.

Check Summary Preview (Software Format; Auto-Populated)

AASHTO LRFD Sec. 11 & ACI 318 Retaining Wall Design Calculator: check summary (software format)
Calculation basis: FHWA GEC 11 (FHWA-HIF-24-002, 2023) / SCDOT GDM (2022) / MnDOT LRFD BDM — AASHTO LRFD Bridge Design Specifications Sec. 11 (9th Ed. 2020 values as published in these free federal/state manuals; not the 10th Ed. text)
Check item Trial value Status
Strength Ia Sliding Resistance φτRn / Hu (φτ = 0.80)1.079 (Rd = 129.7, Ed = 120.2) ≥ 1.000OK
Strength Ia Eccentricity Limit |e|/B0.102 ≤ 0.333OK
Strength Ib Bearing Resistance φbRn / Vu (φb = 0.55)2.767 (Rd = 1109.5, Ed = 400.9) ≥ 1.000OK
Minimum concrete strength27.6 MPa —◇ Not judged
Not judged: The general minimum strengths of ACI 318-19 and EN 1992-1-1 have not been verified against the original text, so no pass/fail judgement is made; the designer may specify a limit with fc_min_mpa.

Summary of the online calculation (software format) for checking by the designer and an independent checker. Final submittals require review and seal by the licensed Professional Engineer in responsible charge.

Desktop edition: calculation reports and cross-module quantity reconciliation

1. Calculation reports: with a license, the desktop edition writes Word (.docx) and Excel (.xlsx) calculation reports and DXF drawings without the trial watermark, listing the inputs, the equations used and the results; in trial mode the step-by-step detail is hidden. For this calculator alone, licensed users can also sign in on the calculator above and formally export a single-tool Word report (with a verification code) and DXF drawing. The Pro plan (all modules) is US$990 per year; see Pricing for monthly, perpetual and team plans.
2. Cross-module reconciliation: desktop project runs carry the design peak flow into downstream channel, culvert and bridge hydraulics; terrain cut/fill into the earthwork balance, cost and carbon tables; structural concrete, formwork and rebar take-off into the cost and carbon tables; slope and excavation safety-factor thresholds into construction monitoring trigger levels.
3. Agency plan reviewers and university faculty can request a complimentary review or teaching license (link below).

Desktop pricing (Pro US$990/yr) Download the desktop trial Complimentary license for agency reviewers and faculty
Scope and responsibility: This page is a single-calculator trial run; cross-module quantity reconciliation is done in desktop project runs. Problems outside this calculator's scope (see the FAQ) need an appropriate analysis method. Final submittals require review and seal by a licensed Professional Engineer.

Governing Equations (US Customary Notation) & Basis Reported by the Calculation Core

The equations and limits the calculation core applies are listed below for independent checking.

Strength Ia / Ib Load Factors by Component (Table 3.4.1-2)
Strength Ia (sliding, eccentricity): γ_DC = 0.90, γ_EV = 1.00, γ_EH = 1.50, γ_LS = 1.75 (lateral; LS on the heel not counted); Strength Ib (bearing): γ_DC = 1.25, γ_EV = 1.35, γ_EH = 1.50, γ_LS = 1.75
Each load component — wall self-weight DC, soil on the heel EV, horizontal earth pressure EH and live-load surcharge LS — is factored separately (Table 3.4.1-2, via MnDOT LRFD BDM §11.4.2 and FHWA GEC 11 Table 18). Strength Ia (minimum vertical, maximum horizontal) governs sliding and eccentricity; Strength Ib (maximum vertical) governs bearing. The eccentricity of the Strength Ia factored resultant is checked against |e| / B ≤ 1/3 (0.333) on soil for the default basis (9th Edition values) and ≤ 1/4 (0.250) for the selectable 4th Ed. (2007) basis.
Factored Sliding & Bearing Resistance with State DOT φ_τ / φ_b Overrides
φ_τ · R_τ + φ_ep · R_ep ≥ H_u (Strength Ia), R_τ = V_u · μ + c_a · B′; q_u = V_u / B′ ≤ φ_b · q_n (Strength Ib), B′ = B − 2·|e|
Default resistance factors (9th Edition values): φ_τ = 0.80 for cast-in-place concrete on sand (Table 10.5.5.2.2-1, via MnDOT) and φ_b = 0.55 (AASHTO Table 11.5.7-1 as reproduced in Colorado DOT Bridge Design Manual Example 11; SCDOT GDM Table 9-6 gives the same value). When custom State DOT factors are entered, the calculation core uses them and tags the basis line of the result as an override. Passive resistance in front of the toe or shear key is counted only when passive soil inputs are given, with φ_ep = 0.50; the base in front of a shear key uses the soil-on-soil value φ_τ = 0.90 (MnDOT p.11-111).
ACI 318 Cantilever Stem & Footing Flexural / Shear Design (ASTM A615 Grade 60)
φM_n = 0.90 · A_s · f_y · (d − a / 2) ≥ M_u, a = (A_s · f_y) / (0.85 · f'_c · b), φV_c = 0.75 · 2√f'_c · b · d ≥ V_u
b = 12 in./ft strip; ASTM A615 Grade 60 bars (#4–#9). Clear cover is set by the calculation core for each member and is not an input of this form; the φM_n and φV_c used in each check are listed in the RC design table of the result.

Worked Example: 15.0-ft CIP Cantilever Retaining Wall (B = 13.0 ft, #6 @ 8 in. o.c.)

The worked example below was computed by the calculation core when this page was built; entering the same inputs above reproduces it. Verification cases, tolerances and actual differences for the calculation core are listed on the Benchmarks page.

AASHTO LRFD Sec. 11 Strength Ia / Ib and ACI 318 check for an H = 15.0 ft cast-in-place RC retaining wall with a B = 13.0 ft base (2.5-ft toe, 1.5-ft stem, 9.0-ft heel), an 18 in. × 18 in. shear key, γ = 120 pcf granular backfill (φ' = 32°), a 250 psf live-load surcharge, f'c = 4,000 psi, and ASTM A615 Grade 60 #6 @ 8 in. o.c. stem steel.

Every number in this example was produced by the calculation core (WebAssembly) when this page was built. The calculation core works in SI units: the US customary inputs below are converted with exact NIST SP 811 factors before the calculation, and results are shown in US customary units with the core's SI value in parentheses. Check values, criteria and calculation steps are the core's own SI output. Basis reported by the core: FHWA GEC 11 (FHWA-HIF-24-002, 2023) / SCDOT GDM (2022) / MnDOT LRFD BDM — AASHTO LRFD Bridge Design Specifications Sec. 11 (9th Ed. 2020 values as published in these free federal/state manuals; not the 10th Ed. text)

1. Input Parameters

Design ParameterUS Customary ValueUnit
Wall Structural TypeRC Inverted-T Wall—
Total Wall Height H15ft
Stem Top Thickness1ft
Stem Base Thickness1.5ft
Footing Slab Thickness1.5ft
Toe Projection2.5ft
Heel Projection9ft
RC Unit Weight γc150pcf
Batter on Front FaceNo—
Backfill Unit Weight γ120pcf
Backfill Friction Angle φ'32°
Backfill Surface Slope β0°
Earth Pressure TheoryRankine Theory—
Live Load Surcharge q_LS250psf
Include Surcharge on HeelNo—
Water Table Height Behind Wall hw(blank)ft
Saturated Backfill Unit Weight γsat(blank)pcf
Base Friction Coeff. μ = tanδ_b0.55—
Base Adhesion ca0psf
Foundation MaterialSoil Foundation—
Bearing Capacity Input ModeUltimate qu / FS—
Nominal Bearing Resistance q_n12000psf
Front Passive Embedment Depth0ft
Passive Soil γ114.5858pcf
Passive Soil φ'30°
Passive Mobilization Factor0.5—
Horizontal Seismic Coeff. kh0—
Vertical Seismic Coeff. kv0—
Monolithic Shear Key Depth1.5ft
Shear Key Width1.5ft
Shear Key Offset from Toe2.5ft
Key Base Sliding PlaneSegmented at key base (soil friction in front of the key, base friction behind it)—
Concrete Strength f'c (ACI 318)4000psi
ASTM A615 Rebar Yield f_y60000psi
Stem Main Vertical Rebar#6 (ASTM)—
Stem Rebar Spacing (o.c.)8in
Toe Slab Rebar Size#5 (ASTM)—
Toe Rebar Spacing6in
Heel Slab Rebar Size#6 (ASTM)—
Heel Rebar Spacing8in
Stem Bar Curtailment Height, alternate bars(blank)ft
Nominal Maximum Aggregate Size(blank)in
Apply Size Effect λs to Footing ShearNo—
Shear Key Main BarSelected by program—
Shear Key Bar Spacing(blank)in
Key-to-Base InterfaceMonolithic (μ = 1.4)—
Key Design Horizontal ForceAutomatic (passive pressure where present)—
Wall Length(blank)ft

2. Computed Results (calculation core output)

OutputResult
Sliding Factor of Safety FS_s (static, unfactored)2.156
Overturning Factor of Safety FS_o (static, unfactored)5.225
Base Width B13 ft (3.962 m)
Max Toe Bearing Pressure q_max1986 psf (95.1 kPa)
LRFD Sliding CDR (φRn / Hu)1.079
LRFD Bearing CDR (φRn / Vu)2.767

Verification Checks (calculation core output)

Verification ItemComputed ResultGoverning Limit / CriterionStatusBasis
Strength Ia Sliding Resistance φτRn / Hu (φτ = 0.80)1.079 (Rd = 129.7, Ed = 120.2)≥ 1.000PASSAASHTO LRFD Table 10.5.5.2.2-1; load factors Table 3.4.1-2 (9th Ed. via MnDOT LRFD BDM p.11-106 to 11-111, FHWA GEC 11 Table 18)
Strength Ia Eccentricity Limit |e|/B0.102≤ 0.333PASSAASHTO LRFD Art. 11.6.3.3 (9th Ed. via SCDOT GDM p.C-9, MnDOT p.11-52)
Strength Ib Bearing Resistance φbRn / Vu (φb = 0.55)2.767 (Rd = 1109.5, Ed = 400.9)≥ 1.000PASSAASHTO LRFD Art. 11.6.3.2; φb = 0.55 per Table 11.5.7-1 (as reproduced in Colorado DOT BDM Example 11; same value in SCDOT GDM Table 9-6)
Minimum concrete strength27.6 MPa—◇ Not judged
Not judged: The general minimum strengths of ACI 318-19 and EN 1992-1-1 have not been verified against the original text, so no pass/fail judgement is made; the designer may specify a limit with fc_min_mpa.
ACI 318-19 / EN 1992-1-1

3. Calculation Steps (calculation core output, SI units)

[HyGeoWorks online preview - not for PE sealing or submittal]
Base width B = 3.962 m, Earth pressure height H = 4.572 m
[Strength I] Hd = 120.23 kN/m, Rh,d = 129.71 kN/m; Vd = 400.92 kN/m, Rv,d = 1109.47 kN/m; |ed|/B (sliding combination) = 0.102, (bearing combination) = 0.057; φ'd = 32.00°, μd = 0.550
US customary equivalents (NIST SP 811 conversion of the SI values reported by the core above; the core summary itself is unchanged)
  Base Width B = 13 ft
  Max Toe Bearing Pressure q_max = 1986 psf
Characteristic Resultants & Base Pressures (1 rows)
CaseKaΣV (kN/m)ΣH (kN/m)Mr (kN·m/m)Mo (kN·m/m)e (m)qmax (kPa)qmin (kPa)
Static / Persistent0.3073303.2477.35682.90130.700.16095.158.0
RC Flexural & Shear Design (ACI 318: f'c = 4000 psi / 27.6 MPa, fy = 60000 psi / 414 MPa) (4 rows)
MemberMu (kN·m)Vu (kN)As,req (cm²)As,min (cm²)RebarφMn (kN·m)φVc (kN)Status
Stem base157.43102.6710.928.23#6 @ 8 in. o.c.200.01259.44PASS
Toe Slab34.8146.992.528.23#5 @ 6 in. o.c.176.62148.36PASS
Heel Slab144.6779.1410.018.23#6 @ 8 in. o.c.200.01157.86PASS
Shear key0.000.000.008.23#4 @ 6 in. o.c. (auto)115.75115.02PASS

Resistance Factors Applied by the Calculation Core, State DOT Overrides & ASTM A615 Rebar Reference

Inputs and outputs are listed with their units; conversion to and from SI is done by the calculation core.

Basis Selected in the CalculatorSliding φ_τ Used by the CoreBearing φ_b Used by the CoreEccentricity Limit on SoilWhere It Appears in the Result
AASHTO LRFD Sec. 11, 9th Edition values (default basis of this page)0.800.55|e| / B ≤ 1/3 (0.333)Table 10.5.5.2.2-1 & Art. 11.6.3.3
AASHTO LRFD 4th Ed. (2007) / FHWA-NHI-10-024 (selectable)1.000.65|e| / B ≤ 1/4 (0.250)Table 11.5.7-1 & Art. 11.6.3.3
State DOT Custom Override (entered by the engineer)Value enteredValue enteredLimit of the selected basisBasis line of the result is tagged as an override
ASTM A615 Gr. 60 Rebar (#4, #5, #6, #7, #8, #9)f_y = 60,000 psiA_b = 0.20, 0.31, 0.44, 0.60, 0.79, 1.00 in.²Spacing entered in inches (e.g. 8 in. o.c.)ACI 318 flexural / shear design table

Frequently Asked Questions (Basis, Scope & Limits)

Common questions about this calculator and its basis are answered below. Final submittals require review and seal by a licensed Professional Engineer.

Which AASHTO LRFD edition and eccentricity limit does this calculator apply?

By default the calculation core reports its basis as FHWA GEC 11 (FHWA-HIF-24-002, 2023) / SCDOT GDM (2022) / MnDOT LRFD BDM, which reproduce the AASHTO LRFD Bridge Design Specifications Sec. 11 factors of the 9th Edition (2020); the text of the 10th Edition (2024) is not used. It checks the Strength Ia resultant eccentricity on soil against |e|/B ≤ 1/3 (0.333) with φ_τ = 0.80 and φ_b = 0.55. Selecting AASHTO LRFD 4th Ed. (2007) / FHWA-NHI-10-024 in the design-code selector switches the limit to |e|/B ≤ 1/4 (0.250) and the default factors to φ_τ = 1.00 and φ_b = 0.65. The basis line and every check row of the result name the edition that was actually applied.

What does the State DOT Custom Resistance Factor (φ_τ / φ_b) Override do?

A State DOT manual may specify resistance factors φ_τ and φ_b that differ from AASHTO Table 11.5.7-1. The calculator lets the engineer enter φ_τ, φ_b and the agency name; the calculation core then uses the entered factors, shows them in the check rows, and tags the basis line of the result as an override so the reviewer can see that the national default was not used.

How is the live-load surcharge (q_LS) modeled?

The surcharge is entered as a uniform pressure q_LS (psf) on the backfill; the worked example uses 250 psf. In the Strength I check the calculation core applies γ_LS = 1.75 to the share of the active thrust caused by the surcharge and γ_EH = 1.50 to the earth-pressure share.

Does the tool output US ASTM A615 rebar callouts (#4–#9 at inch spacings) rather than converted metric bars?

Yes. You select ASTM A615 Grade 60 bars (#4, #5, #6, #7, #8, #9) and enter the spacing in inches, and the RC design table of the result lists the bar callout (for example #6 @ 8 in. o.c.), φM_n, φV_c and the status of each member.

USD Pricing · Checkout by Stripe · Printable USD Quotation

From the Online Preview to the HydroStudio Desktop Edition: Reports Without the Trial Watermark

The free online preview is not for PE sealing or submittal and has no Word report, DXF drawing or verification code. Licensed users can sign in on the calculator and formally export a single-tool Word report (with a verification code) and DXF drawing. Several calculators can be combined in the Project List and exported online as a multi-chapter project report, and projects with terrain or GIS files can run in the heavy cloud computation. For interactive 2D models and large simulations, the HydroStudio desktop edition (Windows 10/11, 64-bit) opens the exported .toml project and, with a license, writes report.docx, a report.xlsx with live formulas and DXF drawings without the trial watermark. Sealing and submittal remain the responsibility of the licensed engineer.

Monthly
Pro monthly
$119 / month
One discipline: $69 / month. Renews monthly until canceled; cancel any time before the next renewal and keep using it to the end of the paid month.
Buy monthly ($119/mo)
30 days
30-day pass
$79 / 30 days, one discipline
All modules: $135. One payment; it does not renew. The pass fee can be credited once toward an annual or perpetual license of the same discipline or a higher plan bought within 30 days after the pass ends, with the same email and in the same currency.
Buy a 30-day pass (from $79)
Quotation
Printable USD quotation
For any plan, including Firm (from 3 seats) and Enterprise (from 10 seats), which are sold only to businesses and other organizations, not to individual buyers: print the quotation or save it as a PDF for your purchasing process.
Request a printable USD quotation

Compare all plans, including 90-day passes and perpetual licenses

Checkout is processed by Stripe; a tax ID can be entered at checkout, and for one-time payments Stripe issues an invoice showing the buyer's name and tax ID. Procurement follows your organization's own rules.

Explore All 31 Tools (20 US Customary + 11 Reference: Basis Stated on Each Page)

Need to edit terrain, 2D flood models and design alternatives interactively on your computer, or see 3D views drawn from your project data? Use the HydroStudio desktop edition:
Download the Desktop Trial
No credit card or phone number is needed to download. Without a license it runs as a trial: local calculation and 3D viewing work, exported reports and drawings carry a trial watermark (not for submittal), and some built-in data libraries are limited. Plans and prices are on the Pricing page.