AASHTO 1993 Flexible Pavement Structural Number (SN) Check
Required structural number SN from the design ESAL W18, reliability R, overall standard deviation S0, initial and terminal serviceability p0 and pt, and subgrade resilient modulus MR, checked against the SN provided by the layer thicknesses (with the SN of each layer tabulated).
Design basis as reported by the calculation core: AASHTO Guide for Design of Pavement Structures (1993) / FHWA NHI-05-037 Appendix C Eqs. C.2, C.3, Table C-3
The calculation is the AASHTO 1993 flexible pavement equation named in the basis line. Layer thicknesses are entered in centimetres and the subgrade modulus in MPa; layer coefficients are per inch, as in the AASHTO guide. Layer and drainage coefficients are input values.
Recalculates in your browser as you edit inputs; Free sample Word report and DXF for this calculator; With a license: formal Word and DXF export, plus online project reports from the Project List.
Check Summary Preview (Software Format; Auto-Populated)
| Check item | Trial value | Status |
|---|---|---|
| Provided SN ≥ required SN | 3.92 ≥ 3.68 | OK |
Summary of the online calculation (software format) for checking by the designer and an independent checker. Final submittals require review and seal by the licensed Professional Engineer in responsible charge.
Desktop edition: calculation reports and cross-module quantity reconciliation
1. Calculation reports: with a license, the desktop edition writes Word (.docx) and Excel (.xlsx) calculation reports and DXF drawings without the trial watermark, listing the inputs, the equations used and the results; in trial mode the step-by-step detail is hidden. For this calculator alone, licensed users can also sign in on the calculator above and formally export a single-tool Word report (with a verification code) and DXF drawing. The Pro plan (all modules) is US$990 per year; see Pricing for monthly, perpetual and team plans.
2. Cross-module reconciliation: desktop project runs carry the design peak flow into downstream channel, culvert and bridge hydraulics; terrain cut/fill into the earthwork balance, cost and carbon tables; structural concrete, formwork and rebar take-off into the cost and carbon tables; slope and excavation safety-factor thresholds into construction monitoring trigger levels.
3. Agency plan reviewers and university faculty can request a complimentary review or teaching license (link below).
Standard example (calculation core defaults)
The worked example below was computed by the calculation core when this page was built; entering the same inputs above reproduces it. Verification cases, tolerances and actual differences for the calculation core are listed on the Benchmarks page.
The standard example uses the default inputs of the calculation core. Every number below was produced by the core when this page was built; nothing on this page is computed by hand.
Every number in this example was produced by the calculation core (WebAssembly) when this page was built. This calculator computes to the documents named in its basis line and works in SI units; use the unit button in the calculator to view US customary equivalents. Basis reported by the core: AASHTO Guide for Design of Pavement Structures (1993) / FHWA NHI-05-037 Appendix C Eqs. C.2, C.3, Table C-3
1. Input Parameters
| Design Parameter | Value | Unit |
|---|---|---|
| Cumulative ESAL W18 | 2000000 | ESAL |
| Reliability R (%) | 90% | — |
| Overall Standard Deviation S0 | 0.45 | — |
| Initial Serviceability Index p0 | 4.2 | — |
| Terminal Serviceability Index pt | 2.5 | — |
| Effective Subgrade Resilient Modulus MR | 60 | MPa |
| Asphalt Surface Course Thickness D1 | 10 | cm |
| Surface Layer Coefficient a1 | 0.44 | — |
| Granular Base Thickness D2 | 20 | cm |
| Base Layer Coefficient a2 | 0.14 | — |
| Base Drainage Coefficient m2 | 1 | — |
| Granular Subbase Thickness D3 | 25 | cm |
| Subbase Layer Coefficient a3 | 0.11 | — |
| Subbase Drainage Coefficient m3 | 1 | — |
2. Computed Results (calculation core output)
| Output | Result |
|---|---|
| Required structural number SN | 3.68 |
| Provided structural number SN | 3.92 |
| W18 capacity of the provided SN | 2969377 ESAL |
Verification Checks (calculation core output)
| Verification Item | Computed Result | Governing Limit / Criterion | Status | Basis |
|---|---|---|---|---|
| Provided SN ≥ required SN | 3.92 | ≥ 3.68 | PASS | AASHTO Guide for Design of Pavement Structures (1993) flexible pavement design equation (FHWA NHI-05-037 Appendix C Eqs. C.2, C.3, Table C-3) |
3. Calculation Steps (calculation core output, SI units)
[HyGeoWorks online preview - not for PE sealing or submittal] Reliability 90.0% → ZR = -1.282; ΔPSI = p0 − pt = 1.70; MR = 60.0 MPa (8702 psi); log10(W18) = 6.301 → required SN = 3.68
Layer structural numbers SN = a·m·D (D in inches) (3 rows)
| Layer | Thickness D (cm) | Layer coefficient a | Drainage coefficient m | SN |
|---|---|---|---|---|
| Surface course | 10.0 | 0.44 | — | 1.73 |
| Base course | 20.0 | 0.14 | 1.00 | 1.10 |
| Subbase course | 25.0 | 0.11 | 1.00 | 1.08 |
Assumptions and Limits Stated by the Calculation Core
- Design equation: AASHTO Guide for Design of Pavement Structures (1993) flexible pavement design equation (FHWA NHI-05-037 Appendix C Eqs. C.2, C.3, Table C-3); the required structural number is solved from Eq. C.2 and the provided SN = Σ a·m·D (D in inches, Eq. C.3)
- Layer coefficients a and drainage coefficients m are inputs (from material tests or agency requirements); FHWA NHI-05-037 mentions typical values of a1 = 0.40-0.44 for dense-graded asphalt concrete, an overall standard deviation of 0.45 and an initial serviceability of 4.2, for reference only
- This check compares the total structural number only; layered minimum-thickness analysis (SN above each layer from the modulus of the layer below), serviceability loss from swelling and frost heave, rigid pavements and overlay design are not included
- This tool applies the AASHTO 1993 design equation; confirm your agency's pavement design requirements, edition and parameters before use
Frequently Asked Questions
Common questions about this calculator and its basis are answered below. Final submittals require review and seal by a licensed Professional Engineer.
Which design basis does this calculator apply?
AASHTO Guide for Design of Pavement Structures (1993) / FHWA NHI-05-037 Appendix C Eqs. C.2, C.3, Table C-3. The calculation is the AASHTO 1993 flexible pavement equation named in the basis line. Layer thicknesses are entered in centimetres and the subgrade modulus in MPa; layer coefficients are per inch, as in the AASHTO guide. Layer and drainage coefficients are input values.
What assumptions and limits does the calculation core state for this tool?
Design equation: AASHTO Guide for Design of Pavement Structures (1993) flexible pavement design equation (FHWA NHI-05-037 Appendix C Eqs. C.2, C.3, Table C-3); the required structural number is solved from Eq. C.2 and the provided SN = Σ a·m·D (D in inches, Eq. C.3). Layer coefficients a and drainage coefficients m are inputs (from material tests or agency requirements); FHWA NHI-05-037 mentions typical values of a1 = 0.40-0.44 for dense-graded asphalt concrete, an overall standard deviation of 0.45 and an initial serviceability of 4.2, for reference only. This check compares the total structural number only; layered minimum-thickness analysis (SN above each layer from the modulus of the layer below), serviceability loss from swelling and frost heave, rigid pavements and overlay design are not included. This tool applies the AASHTO 1993 design equation; confirm your agency's pavement design requirements, edition and parameters before use.
Where is the calculation performed, and can the result be sealed or submitted?
The calculation runs in your browser, in the same WebAssembly calculation core this page loads. The result is an online preview: its first line reads "[HyGeoWorks online preview - not for PE sealing or submittal]".
Can I recalculate without a network connection?
Yes. "Download the offline workbench" on this page saves one HTML file that contains the workbench and the same calculation core; opened from disk it recalculates without a network connection.
From the Online Preview to the HydroStudio Desktop Edition: Reports Without the Trial Watermark
The free online preview is not for PE sealing or submittal and has no Word report, DXF drawing or verification code. Licensed users can sign in on the calculator and formally export a single-tool Word report (with a verification code) and DXF drawing. Several calculators can be combined in the Project List and exported online as a multi-chapter project report, and projects with terrain or GIS files can run in the heavy cloud computation. For interactive 2D models and large simulations, the HydroStudio desktop edition (Windows 10/11, 64-bit) opens the exported .toml project and, with a license, writes report.docx, a report.xlsx with live formulas and DXF drawings without the trial watermark. Sealing and submittal remain the responsibility of the licensed engineer.
Compare all plans, including 90-day passes and perpetual licenses