Check Summary Preview (Software Format; Auto-Populated)
| Check item | Trial value | Status |
|---|---|---|
| Provided SN ≥ required SN | 3.92 ≥ 3.68 | OK |
Summary of the online calculation (software format) for checking by the designer and an independent checker. Final sign-off remains the responsibility of the chartered or registered engineer.
Desktop edition: calculation reports and cross-module quantity reconciliation
1. Calculation reports: with a licence, the desktop edition writes Word (.docx) and Excel (.xlsx) calculation reports and DXF drawings without the trial watermark, listing the inputs, the equations used and the results; in trial mode the step-by-step detail is hidden. For this calculator alone, licensed users can also sign in on the calculator above and formally export a single-tool Word report (with a verification code) and DXF drawing. The Pro plan (all modules) is US$990 per year; see Pricing for monthly, perpetual and team plans.
2. Cross-module reconciliation: desktop project runs carry the design peak flow into downstream channel, culvert and bridge hydraulics; terrain cut/fill into the earthwork balance, cost and carbon tables; structural concrete, formwork and rebar take-off into the cost and carbon tables; slope and excavation safety-factor thresholds into construction monitoring trigger levels.
3. Independent checking engineers, authority reviewers and academics can request a complimentary review or teaching licence (link below).
1. Worked Standard Example (Computed by the Calculation Core)
The worked example below was computed by the calculation core when this page was built; entering the same inputs above reproduces it.
Design Scenario — Standard example (calculation core defaults): The standard example uses the default inputs of the calculation core. Every number below was produced by the core when this page was built; nothing on this page is computed by hand.
The inputs below were passed to the calculation core (WebAssembly) when this page was built; every step, result and check shown here is the core's own output. Basis reported by the core: AASHTO Guide for Design of Pavement Structures (1993) / FHWA NHI-05-037 Appendix C Eqs. C.2, C.3, Table C-3
Inputs Passed to the Calculation Core
| Parameter | Value | Unit |
|---|---|---|
| Cumulative ESAL W18 | 2000000 | ESAL |
| Reliability R (%) | 90% | — |
| Overall Standard Deviation S0 | 0.45 | — |
| Initial Serviceability Index p0 | 4.2 | — |
| Terminal Serviceability Index pt | 2.5 | — |
| Effective Subgrade Resilient Modulus MR | 60 | MPa |
| Asphalt Surface Course Thickness D1 | 10 | cm |
| Surface Layer Coefficient a1 | 0.44 | — |
| Granular Base Thickness D2 | 20 | cm |
| Base Layer Coefficient a2 | 0.14 | — |
| Base Drainage Coefficient m2 | 1 | — |
| Granular Subbase Thickness D3 | 25 | cm |
| Subbase Layer Coefficient a3 | 0.11 | — |
| Subbase Drainage Coefficient m3 | 1 | — |
Calculation Steps (calculation core output)
[HyGeoWorks online preview - not for PE sealing or submittal]
- Reliability 90.0% → ZR = -1.282; ΔPSI = p0 − pt = 1.70; MR = 60.0 MPa (8702 psi); log10(W18) = 6.301 → required SN = 3.68
Computed Results (calculation core output)
| Output Parameter | Calculated Value | SI Unit |
|---|---|---|
| Required structural number SN | 3.68 | — |
| Provided structural number SN | 3.92 | — |
| W18 capacity of the provided SN | 2969377 | ESAL |
Verification Checks (calculation core output)
| Verification Check | Computed Value | Criterion | Verdict | Basis |
|---|---|---|---|---|
| Provided SN ≥ required SN | 3.92 | ≥ 3.68 | OK | AASHTO Guide for Design of Pavement Structures (1993) flexible pavement design equation (FHWA NHI-05-037 Appendix C Eqs. C.2, C.3, Table C-3) |
Layer structural numbers SN = a·m·D (D in inches) (3 rows)
| Layer | Thickness D (cm) | Layer coefficient a | Drainage coefficient m | SN |
|---|---|---|---|---|
| Surface course | 10.0 | 0.44 | — | 1.73 |
| Base course | 20.0 | 0.14 | 1.00 | 1.10 |
| Subbase course | 25.0 | 0.11 | 1.00 | 1.08 |
Assumptions and Limits Stated by the Calculation Core
- Design equation: AASHTO Guide for Design of Pavement Structures (1993) flexible pavement design equation (FHWA NHI-05-037 Appendix C Eqs. C.2, C.3, Table C-3); the required structural number is solved from Eq. C.2 and the provided SN = Σ a·m·D (D in inches, Eq. C.3)
- Layer coefficients a and drainage coefficients m are inputs (from material tests or agency requirements); FHWA NHI-05-037 mentions typical values of a1 = 0.40-0.44 for dense-graded asphalt concrete, an overall standard deviation of 0.45 and an initial serviceability of 4.2, for reference only
- This check compares the total structural number only; layered minimum-thickness analysis (SN above each layer from the modulus of the layer below), serviceability loss from swelling and frost heave, rigid pavements and overlay design are not included
- This tool applies the AASHTO 1993 design equation; confirm your agency's pavement design requirements, edition and parameters before use
2. Frequently Asked Questions
Common questions about this calculator are answered below. Final sign-off remains the responsibility of the chartered or registered engineer.
Which design basis does this calculator apply?
AASHTO Guide for Design of Pavement Structures (1993) / FHWA NHI-05-037 Appendix C Eqs. C.2, C.3, Table C-3. The calculation is the AASHTO 1993 flexible pavement equation named in the basis line. Layer thicknesses are entered in centimetres and the subgrade modulus in MPa; layer coefficients are per inch, as in the AASHTO guide. Layer and drainage coefficients are input values.
What assumptions and limits does the calculation core state for this tool?
Design equation: AASHTO Guide for Design of Pavement Structures (1993) flexible pavement design equation (FHWA NHI-05-037 Appendix C Eqs. C.2, C.3, Table C-3); the required structural number is solved from Eq. C.2 and the provided SN = Σ a·m·D (D in inches, Eq. C.3). Layer coefficients a and drainage coefficients m are inputs (from material tests or agency requirements); FHWA NHI-05-037 mentions typical values of a1 = 0.40-0.44 for dense-graded asphalt concrete, an overall standard deviation of 0.45 and an initial serviceability of 4.2, for reference only. This check compares the total structural number only; layered minimum-thickness analysis (SN above each layer from the modulus of the layer below), serviceability loss from swelling and frost heave, rigid pavements and overlay design are not included. This tool applies the AASHTO 1993 design equation; confirm your agency's pavement design requirements, edition and parameters before use.
Where is the calculation performed, and can the result be sealed or submitted?
The calculation runs in your browser, in the same WebAssembly calculation core this page loads. The result is an online preview: its first line reads "[HyGeoWorks online preview - not for PE sealing or submittal]".
Can I recalculate without a network connection?
Yes. "Download the offline workbench" on this page saves one HTML file that contains the workbench and the same calculation core; opened from disk it recalculates without a network connection.
3. Explore All 30 Calculators (SI Edition; Design Basis Stated on Each Page)
Each calculator below states its own design basis on its page; several apply Taiwan regulations and say so.