Check Summary Preview (Software Format; Auto-Populated)
| Check item | Trial value | Status |
|---|---|---|
| Available sight distance ≥ required stopping sight distance | 90.0 m ≥ 70.0 m | OK |
| Grade 0-50 m | 3.00% ≤ 8.00% | OK |
| Grade 50-100 m | 2.00% ≤ 8.00% | OK |
| Crest vertical curve length (PVI at 50 m, grade difference 5.00%) | 100.00 m ≥ 65.00 m | OK |
| Horizontal curve C1 radius | 150.00 m ≥ 120.00 m | OK |
| Horizontal curve C1 spiral length | 75.00 m ≥ 38.30 m | OK |
Summary of the online calculation (software format) for checking by the designer and an independent checker. Final sign-off remains the responsibility of the chartered or registered engineer.
Desktop edition: calculation reports and cross-module quantity reconciliation
1. Calculation reports: with a licence, the desktop edition writes Word (.docx) and Excel (.xlsx) calculation reports and DXF drawings without the trial watermark, listing the inputs, the equations used and the results; in trial mode the step-by-step detail is hidden. For this calculator alone, licensed users can also sign in on the calculator above and formally export a single-tool Word report (with a verification code) and DXF drawing. The Pro plan (all modules) is US$990 per year; see Pricing for monthly, perpetual and team plans.
2. Cross-module reconciliation: desktop project runs carry the design peak flow into downstream channel, culvert and bridge hydraulics; terrain cut/fill into the earthwork balance, cost and carbon tables; structural concrete, formwork and rebar take-off into the cost and carbon tables; slope and excavation safety-factor thresholds into construction monitoring trigger levels.
3. Independent checking engineers, authority reviewers and academics can request a complimentary review or teaching licence (link below).
1. Worked Standard Example (Computed by the Calculation Core)
The worked example below was computed by the calculation core when this page was built; entering the same inputs above reproduces it.
Design Scenario — Standard example (calculation core defaults): The standard example uses the default inputs of the calculation core. Every number below was produced by the core when this page was built; nothing on this page is computed by hand.
The inputs below were passed to the calculation core (WebAssembly) when this page was built; every step, result and check shown here is the core's own output. Basis reported by the core: MOTC (Taiwan) Highway Route Design Code (2026-07 ed.) Tables 3.2, 3.3.1.1, 3.4, 3.10.2, 3.13; Taiwan Farm Road Design Code (amended 2019-10-28)
Inputs Passed to the Calculation Core
| Parameter | Value | Unit |
|---|---|---|
| Road Category | Highway (Taiwan Highway Route Design Code) | — |
| Design Speed Vd (km/h) | 60 km/h | — |
| Maximum Superelevation emax | 8% (0.08) | — |
| Check Against Recommended Values | No | — |
| Horizontal Curve Radius R | 150 | m |
| Transition Curve Length Ls | 75 | m |
| Available Stopping Sight Distance S | 90 | m |
| Approach Grade G1 | 3 | % |
| Departure Grade G2 | -2 | % |
| Vertical Curve Length Lv | 100 | m |
Calculation Steps (calculation core output)
[HyGeoWorks online preview - not for PE sealing or submittal]
- Design speed Vd = 60 km/h (checked against allowable values); grades G1 = 3.00%, G2 = -2.00%, grade difference ΔG = 5.00% (crest vertical curve)
Computed Results (calculation core output)
| Output Parameter | Calculated Value | SI Unit |
|---|---|---|
| Required stopping sight distance | 70.0 | m |
| Minimum horizontal curve radius Rmin | 120.0 | m |
| Maximum grade | 8.00 | % |
| Provided vertical curve K = Lv/ΔG | 20.00 | m/% |
| Required vertical curve length | 65.0 | m |
Verification Checks (calculation core output)
| Verification Check | Computed Value | Criterion | Verdict | Basis |
|---|---|---|---|---|
| Available sight distance ≥ required stopping sight distance | 90.0 m | ≥ 70.0 m | OK | MOTC (Taiwan) Highway Route Design Code (2026-07 ed.) Table 3.3.1.1 |
| Grade 0-50 m | 3.00% | ≤ 8.00% | OK | MOTC (Taiwan) Highway Route Design Code (2026-07 ed.) (maximum grade) |
| Grade 50-100 m | 2.00% | ≤ 8.00% | OK | MOTC (Taiwan) Highway Route Design Code (2026-07 ed.) (maximum grade) |
| Crest vertical curve length (PVI at 50 m, grade difference 5.00%) | 100.00 m | ≥ 65.00 m | OK | MOTC (Taiwan) Highway Route Design Code (2026-07 ed.) (Lv = K·ΔG, and not less than the minimum vertical curve length) |
| Horizontal curve C1 radius | 150.00 m | ≥ 120.00 m | OK | MOTC (Taiwan) Highway Route Design Code (2026-07 ed.) (minimum curve radius) |
| Horizontal curve C1 spiral length | 75.00 m | ≥ 38.30 m | OK | MOTC (Taiwan) Highway Route Design Code (2026-07 ed.) 3.6.1 (Ls ≥ Vd³/(47·J·R); radius 500 m or more may omit the spiral) |
Assumptions and Limits Stated by the Calculation Core
- Check values are taken from MOTC (Taiwan) Highway Route Design Code (2026-07 ed.) (tabulated values); the minimum radii in Table 3.4 are not a consistent rounding of Vd²/(127(emax + fs)), so the tabulated values govern
- Sight distance is a comparison of the entered available sight distance with the tabulated value; sight lines are not computed from the horizontal and vertical geometry. Passing sight distance, superelevation runoff, composite grade, grade length limits and curve widening are not checked. PVI stations are derived from the vertical curve length (each adjacent tangent is half the curve length and not less than 50 m)
2. Frequently Asked Questions
Common questions about this calculator are answered below. Final sign-off remains the responsibility of the chartered or registered engineer.
Which design basis does this calculator apply?
MOTC (Taiwan) Highway Route Design Code (2026-07 ed.) Tables 3.2, 3.3.1.1, 3.4, 3.10.2, 3.13; Taiwan Farm Road Design Code (amended 2019-10-28). All tabulated limits come from the Taiwan highway and farm road design codes named in the basis line. They are not AASHTO Green Book, DMRB or Austroads values; use the result as a reference calculation and check the standards of your own authority.
What assumptions and limits does the calculation core state for this tool?
Check values are taken from MOTC (Taiwan) Highway Route Design Code (2026-07 ed.) (tabulated values); the minimum radii in Table 3.4 are not a consistent rounding of Vd²/(127(emax + fs)), so the tabulated values govern. Sight distance is a comparison of the entered available sight distance with the tabulated value; sight lines are not computed from the horizontal and vertical geometry. Passing sight distance, superelevation runoff, composite grade, grade length limits and curve widening are not checked. PVI stations are derived from the vertical curve length (each adjacent tangent is half the curve length and not less than 50 m).
Where is the calculation performed, and can the result be sealed or submitted?
The calculation runs in your browser, in the same WebAssembly calculation core this page loads. The result is an online preview: its first line reads "[HyGeoWorks online preview - not for PE sealing or submittal]".
Can I recalculate without a network connection?
Yes. "Download the offline workbench" on this page saves one HTML file that contains the workbench and the same calculation core; opened from disk it recalculates without a network connection.
3. Explore All 30 Calculators (SI Edition; Design Basis Stated on Each Page)
Each calculator below states its own design basis on its page; several apply Taiwan regulations and say so.