Check Summary Preview (Software Format; Auto-Populated)
| Check item | Trial value | Status |
|---|---|---|
| Min. Stone Size d | 0.496 m | Calculated value |
| Min. Apron Width W | 3.00 m | Calculated value |
| Min. Apron Length L | 4.00 m | Calculated value |
| HEC-23 Median Riprap D50 | 0.262 m | Calculated value |
Summary of the online calculation (software format) for checking by the designer and an independent checker. Final sign-off remains the responsibility of the chartered or registered engineer.
Desktop edition: calculation reports and cross-module quantity reconciliation
1. Calculation reports: with a licence, the desktop edition writes Word (.docx) and Excel (.xlsx) calculation reports and DXF drawings without the trial watermark, listing the inputs, the equations used and the results; in trial mode the step-by-step detail is hidden. For this calculator alone, licensed users can also sign in on the calculator above and formally export a single-tool Word report (with a verification code) and DXF drawing. The Pro plan (all modules) is US$990 per year; see Pricing for monthly, perpetual and team plans.
2. Cross-module reconciliation: desktop project runs carry the design peak flow into downstream channel, culvert and bridge hydraulics; terrain cut/fill into the earthwork balance, cost and carbon tables; structural concrete, formwork and rebar take-off into the cost and carbon tables; slope and excavation safety-factor thresholds into construction monitoring trigger levels.
3. Independent checking engineers, authority reviewers and academics can request a complimentary review or teaching licence (link below).
1. Governing Equations & SI Nomenclature
The equations the calculation core applies are summarised below for independent checking.
The equations below summarise the method that the calculation core applies on this page. The design basis it reports is: MOTC (Taiwan) Highway Drainage Design Code §5.13 Eq. 5-3 (stone size and apron dimensions); FHWA HEC-23 Vol. 1 Eq. 5.1 (Isbash D50, for reference). The worked example further down lists the core's own calculation steps for the standard example.
2. Worked Standard Example (Computed by the Calculation Core)
The worked example below was computed by the calculation core when this page was built; entering the same inputs above reproduces it.
Design Scenario — Riprap Apron at a 1.20 m Wide Drain Outlet (V = 3.50 m/s, Ss = 2.65): Size the stone and the minimum apron width and length at the outlet of a drain 1.20 m wide and 0.80 m deep discharging at V = 3.50 m/s, with rock of specific gravity 2.65.
The inputs below were passed to the calculation core (WebAssembly) when this page was built; every step, result and check shown here is the core's own output. Basis reported by the core: MOTC (Taiwan) Highway Drainage Design Code §5.13 Eq. 5-3 (stone size and apron dimensions); FHWA HEC-23 Vol. 1 Eq. 5.1 (Isbash D50, for reference)
Inputs Passed to the Calculation Core
| Parameter | Value | Unit |
|---|---|---|
| Outlet Velocity V | 3.5 | m/s |
| Drain Channel Width | 1.2 | m |
| Drain Channel Depth | 0.8 | m |
| Riprap Specific Gravity Ss | 2.65 | — |
Calculation Steps (calculation core output)
[HyGeoWorks online preview - not for PE sealing or submittal]
- d = V²/24.7 = 3.5²/24.7 = 0.496 m
- Min. apron width >= 2.5 * channel width = 3.00 m; min. apron length >= 5.0 * channel depth = 4.00 m
- FHWA HEC-23 Eq. 5.1: D50 = 0.692·V²/(2g(Ss − 1)) = 0.262 m (K = 1.0)
Computed Results (calculation core output)
| Output Parameter | Calculated Value | SI Unit |
|---|---|---|
| Min. Stone Size d | 0.496 | m |
| Min. Apron Width W | 3.00 | m |
| Min. Apron Length L | 4.00 | m |
| HEC-23 Median Riprap D50 | 0.262 | m |
3. Regional Design Options in This Edition: UK, EU, Singapore, Malaysia, Hong Kong & Australia
Symbols and units are SI unless stated otherwise.
- This calculator: the design basis is the one reported by the calculation core: MOTC (Taiwan) Highway Drainage Design Code §5.13 Eq. 5-3 (stone size and apron dimensions); FHWA HEC-23 Vol. 1 Eq. 5.1 (Isbash D50, for reference). The options listed below belong to the calculators named in each item.
- United Kingdom, Ireland & European Union: The retaining wall and slope stability calculators default to EN 1997-1:2004 Design Approach 1 (Combination 1 & Combination 2); the UK National Annex and 2nd-Gen EN 1997-1:2024 / EN 1997-3:2025 (MFA, and RFA for retaining walls) are selectable there, as are DA2 for retaining walls and DA3 for slopes. The retaining wall calculator lets γG, γQ and γφ' be overridden for a National Annex and designs metric H-bars (H10–H32) when concrete and steel strengths are entered.
- Singapore & Malaysia: The retaining wall calculator offers SS EN 1997-1:2010 with the Singapore National Annex, and the detention calculator offers a DID Malaysia MSMA 2nd Edition (2012) Equation 2.2 IDF rainfall mode besides directly entered design intensities.
- Hong Kong SAR: HyGeoWorks does not claim Hong Kong Buildings Department pre-accepted program status; the retaining wall calculator's HK GEO Geoguide 1 option shows the calculation core's steps and checks so that the result can be checked independently. With that option the calculation core applies the Geoguide 1 Table 6 and Table 7 partial factors at ULS and the §9.2.4 middle-third eccentricity check at SLS.
- Australia & New Zealand: No ARR 2019 IFD data is built in; design rainfall intensities for any AEP can be entered directly in the detention calculator. The HydroStudio desktop edition supports GDA2020 / MGA2020 zones 46–59 as well as WGS 84 / UTM zones.
4. Frequently Asked Questions
Common questions about this calculator are answered below. Final sign-off remains the responsibility of the chartered or registered engineer.
Which formula sets the stone size on this page?
The governing stone size is d = V²/24.7, not less than 0.30 m, with an apron at least 2.5 times the channel width and 5 times the channel depth, per MOTC (Taiwan) Highway Drainage Design Code §5.13 Eq. 5-3, as reported by the calculation core. The FHWA HEC-23 Isbash D50 is listed for reference only.
Why do the two stone sizes differ?
They come from different methods: the highway-code formula is an empirical size based on velocity only, while the Isbash equation is a stability relation that also depends on the rock's specific gravity. The page reports both so the difference is visible; the governing minimum stone size is the highway-code value.
Does the calculator design the filter layer or apron thickness?
No. Riprap placed directly on fine soil can lose that soil through its voids, so a geotextile or graded granular filter is normally provided beneath it. Filter design, blanket thickness and toe details are not computed here and should follow your project specification.
What if the required stone is impractically large?
Consider an energy dissipator instead of a loose rock apron. The HydroStudio desktop edition includes chute and stilling basin design with USBR Type II, III and IV and SAF basins, and the online Drop Structure calculator sizes drop stilling basins.
5. Explore All 30 Calculators (SI Edition; Design Basis Stated on Each Page)
Each calculator below states its own design basis on its page; several apply Taiwan regulations and say so.