GSA Low Embodied Carbon Limits for Concrete and Steel (Interim IRA Material Requirements) with EPA Fuel and Freight Factors
Global warming potential limits quoted from the U.S. General Services Administration document Interim IRA Low Embodied Carbon Material Requirements dated May 16, 2023, together with two factors from the U.S. EPA GHG Emission Factors Hub (2025). The steel limits are the figures held in the platform's code library; the library's concrete entries differ from this GSA table, so the concrete rows below are taken directly from the GSA document.
Reference chart
→ Open the project carbon screening calculator (public emission-factor datasets)
| Material | Top 20% limit | Top 40% limit | Better than average limit | Unit |
|---|---|---|---|---|
| Concrete, specified strength up to 2,499 psi | 228 | 261 | 277 | kgCO2e per cubic meter |
| Concrete, 3,000 psi | 257 | 291 | 318 | kgCO2e per cubic meter |
| Concrete, 4,000 psi | 284 | 326 | 352 | kgCO2e per cubic meter |
| Concrete, 5,000 psi | 305 | 357 | 382 | kgCO2e per cubic meter |
| Concrete, 6,000 psi | 319 | 374 | 407 | kgCO2e per cubic meter |
| Concrete, 7,200 psi and above | 321 | 362 | 402 | kgCO2e per cubic meter |
| Steel rebar, unfabricated | 611 | 716 | 760 | kgCO2e per metric ton |
| Steel rebar, fabricated | 728 | 794 | 850 | kgCO2e per metric ton |
| Hot-rolled structural sections, unfabricated | 686 | 713 | 869 | kgCO2e per metric ton |
| Hot-rolled structural sections, fabricated | 1,022 | 1,128 | 1,163 | kgCO2e per metric ton |
Notes and Limits of Applicability
- High early strength concrete: the GSA document says to add 30% to these numbers for GWP limits where high early strength mixes are required for technical reasons. It contains no separate lightweight concrete table.
- The third column is labeled the Better Than Average limit in the GSA document; it is not an industry average.
- GSA has issued a later version of these requirements (December 2023); confirm the figures against the GSA edition that governs your contract.
- U.S. EPA GHG Emission Factors Hub (2025): Table 2 gives 10.21 kg CO2 per gallon for diesel fuel; Table 8 gives 0.186 kg CO2 per short ton-mile for medium- and heavy-duty truck freight.
Frequently Asked Questions
Which GSA document do these limits come from?
The Interim IRA Low Embodied Carbon Material Requirements published by the U.S. General Services Administration and dated May 16, 2023. Limits are stated by material and, for concrete, by specified compressive strength.
Do the calculator's concrete benchmarks equal this chart?
Not at present. The steel entries in the platform's code library equal the GSA figures charted here, while its concrete entries differ from them. The calculator compares concrete with a GSA limit only when a product EPD value is entered; use the chart figures for GSA comparisons and state the document edition in the submittal.
Sources and disclaimer: figures on these charts are drawn from the platform's code-constants library, from steel producers' published section data, or from the U.S. Government publications named beside each entry (FHWA, USDA, OSHA, FEMA, EPA and GSA). Naming a publication does not imply endorsement by any agency. Consensus standards (ACI, ASTM, AASHTO, AISC) are identified by designation only and none of their text is reproduced. The charts are a design aid rather than an official document, so confirm each figure against the current source. Engineering submittals remain the responsibility of the licensed professional engineer who seals them.